-->

Thursday, February 8, 2018

Category 5 cable, commonly referred to as Cat 5, is a twisted pair cable for computer networks. The cable standard provides performance of up to 100 MHz and is suitable for most varieties of Ethernet over twisted pair. Cat 5 is also used to carry other signals such as telephony and video.

This cable is commonly connected using punch-down blocks and modular connectors. Most Category 5 cables are unshielded, relying on the balanced line twisted pair design and differential signaling for noise rejection.

The category 5 specification was deprecated in 2001 and is superseded by the category 5e specification.

Cable standard


Low end thin UTP CAT5 cable RJ45 network cable Ethernet cable ...
Low end thin UTP CAT5 cable RJ45 network cable Ethernet cable .... Source : www.aliexpress.com

The specification for category 5 cable was defined in ANSI/TIA/EIA-568-A, with clarification in TSB-95. These documents specify performance characteristics and test requirements for frequencies up to 100 MHz.

The cable is available in both stranded and solid conductor forms. The stranded form is more flexible and withstands more bending without breaking. Patch cables are stranded. Permanent wiring used in structured cabling is solid-core. The category and type of cable can be identified by the printing on the jacket.

Termination


24-4P-L5-EN-DB - Category 5e U/UTP EN series 24 AWG 4 pair ...
24-4P-L5-EN-DB - Category 5e U/UTP EN series 24 AWG 4 pair .... Source : secure.libertycable.com

Cable types, connector types and cabling topologies are defined by TIA/EIA-568-B. Nearly always, 8P8C modular connectors (often referred to as RJ45 connectors) are used for connecting category 5 cable. The cable is terminated in either the T568A scheme or the T568B scheme. The two schemes work equally well and may be mixed in an installation so long as the same scheme is used on both ends of each cable.

Variants and comparisons


CAT5e CAT6 Drum/Reel, CAT5 CAT6 UTP Ethernet Network Cable ...
CAT5e CAT6 Drum/Reel, CAT5 CAT6 UTP Ethernet Network Cable .... Source : www.thatcable.com

The category 5e specification improves upon the category 5 specification by revising and introducing new specifications to further mitigate the amount of crosstalk. The bandwidth (100 MHz) and physical construction are the same between the two, and most Cat 5 cables actually meet Cat 5e specifications, though they are not specifically certified as such. The category 5 was deprecated in 2001 and superseded by the category 5e specification.

The category 6 specification improves upon the category 5e specification by improving frequency response and further reducing crosstalk. The improved performance of Cat 6 provides 250 MHz bandwidth and supports 10GBASE-T (10-Gigabit Ethernet) for distances up to 55 meters. Category 6A cable provides 500 MHz bandwidth and supports 10GBASE-T for distances up to 100 meters. Both variants are backwards compatible with category 5 and 5e cables.

Applications


308-605WH - LAN Solutions Category 5e U/UTP pre-made patch cable
308-605WH - LAN Solutions Category 5e U/UTP pre-made patch cable. Source : secure.libertycable.com

Category 5 cable is used in structured cabling for computer networks such as Ethernet over twisted pair. The cable standard provides performance of up to 100 MHz and is suitable for 10BASE-T, 100BASE-TX (Fast Ethernet), and 1000BASE-T (Gigabit Ethernet). 10BASE-T and 100BASE-TX Ethernet connections require two wire pairs. 1000BASE-T Ethernet connections require four wire pairs. Through the use of power over Ethernet (PoE), power can be carried over the cable in addition to Ethernet data.

Cat 5 is also used to carry other signals such as telephony and video. In some cases, multiple signals can be carried on a single cable; Cat 5 can carry two conventional telephone lines as well as 100BASE-TX in a single cable. The USOC/RJ-61 wiring standard may be used in multi-line telephone connections. Various schemes exist for transporting both analog and digital video over the cable. HDBaseT (10.2 Gbit/s) is one such scheme.

Characteristics


Ideal RJ-45 8-Position 8-Contact Category 5e Modular Plugs (25 per ...
Ideal RJ-45 8-Position 8-Contact Category 5e Modular Plugs (25 per .... Source : www.homedepot.com

The use of balanced lines helps preserve a high signal-to-noise ratio despite interference from both external sources and crosstalk from other pairs.

Insulation

Outer insulation is typically polyvinyl chloride (PVC) or low smoke zero halogen (LSOH).

Bending radius

Most Category 5 cables can be bent at any radius exceeding approximately four times the outside diameter of the cable.

Maximum cable segment length

The maximum length for a cable segment is 100 m per TIA/EIA 568-5-A. If longer runs are required, the use of active hardware such as a repeater or switch is necessary. The specifications for 10BASE-T networking specify a 100-meter length between active devices. This allows for 90 meters of solid-core permanent wiring, two connectors and two stranded patch cables of 5 meters, one at each end.

Conductors

Since 1995, solid-conductor UTP cables for backbone cabling is required to be no thicker than 22 American Wire Gauge (AWG) and no thinner than 24 AWG, or 26 AWG for shorter-distance cabling. This standard has been retained with the 2009 revision of ANSI TIA/EIA 568.

Although cable assemblies containing 4 pairs are common, category 5 is not limited to 4 pairs. Backbone applications involve using up to 100 pairs.

Individual twist lengths

The distance per twist is commonly referred to as pitch. Each of the four pairs in a Cat 5 cable has differing precise pitch to minimize crosstalk between the pairs. The pitch of the twisted pairs is not specified in the standard. Measurements on one sample of Cat 5 cable yielded the following results.

Since the pitch of the various colors is not specified in the standard, pitch can vary according to manufacturer and should be measured for the batch being used if cable is being used in non-Ethernet situation where pitch might be critical.

Environmental ratings

Some cables are "UV-rated" or "UV-stable" meaning they can be exposed to outdoor UV radiation without significant destruction.

Plenum-rated cables are slower to burn and produce less smoke than cables using a mantle of materials like PVC. Plenum-rated cables may be installed in plenum spaces where PVC is not allowed.

Shielded cables (FTP or STP) are useful for environments where proximity to RF equipment may introduce electromagnetic interference, and can also be used where eavesdropping likelihood should be minimized.

References


Modeling Category 5 cable for DVI/HDMI links | EE Times
Modeling Category 5 cable for DVI/HDMI links | EE Times. Source : www.eetimes.com


CAT5E-4C-J - Structured Solutions 4 x U/UTP Category 5e jacketed ...
CAT5E-4C-J - Structured Solutions 4 x U/UTP Category 5e jacketed .... Source : www.libertycable.com

 
Sponsored Links