Frame rate (expressed in frames per second or fps) is the frequency (rate) at which consecutive images called frames appear on a display. The term applies equally to film and video cameras, computer graphics, and motion capture systems. Frame rate may also be called the frame frequency, and be expressed in hertz.
Frame rate and human vision
How Many FPS Can Your Eye See? - It's technically an incorrect question, because the human eye doesn't see in "frames." But in all seriousness, how many frames on - say - a gaming monitor can the human eye perceive? Let's...
The temporal sensitivity and resolution of human vision varies depending on the type and characteristics of visual stimulus, and it differs between individuals. The human visual system can process 10 to 12 images per second and perceive them individually, while higher rates are perceived as motion. Modulated light (such as a computer display) is perceived as stable by the majority of participants in studies when the rate is higher than 50Â Hz through 90Â Hz. This perception of modulated light as steady is known as the flicker fusion threshold. However, when the modulated light is non-uniform and contains an image, the flicker fusion threshold can be much higher, in the hundreds of hertz. With regard to image recognition, people have been found to recognize a specific image in an unbroken series of different images, each of which lasts as little as 13 milliseconds. Persistence of vision sometimes accounts for very short single-millisecond visual stimulus having a perceived duration of between 100Â ms and 400Â ms. Multiple stimuli that are very short are sometimes perceived as a single stimulus, such as a 10Â ms green flash of light immediately followed by a 10Â ms red flash of light perceived as a single yellow flash of light.
Film and video
Silent films
Early silent films had stated frame rates anywhere from 16 to 24 frames per second (fps), but since the cameras were hand-cranked, the rate often changed during the scene to fit the mood. Projectionists could also change the frame rate in the theater by adjusting a rheostat controlling the voltage powering the film-carrying mechanism in the projector. Film companies often intended that theaters show their silent films at higher frame rates than they were filmed at. These frame rates were enough for the sense of motion, but it was perceived as jerky motion. To minimize the perceived flicker, projectors employed dual- and triple-blade shutters, so each frame was displayed two or three times, increasing the flicker rate to 48 or 72 Hertz and reducing eye strain. Thomas Edison said that 46 frames per second was the minimum needed for the eye to perceive motion: "Anything less will strain the eye." In the mid to late 1920s, the frame rate for silent films increased to between 20 and 26Â fps.
Sound films
When sound film was introduced in 1926, variations in film speed were no longer tolerated, as the human ear is more sensitive to changes in audio frequency. Many theaters had shown silent films at 22 to 26 fpsâ€"which is why the industry chose 24 fps for sound as a compromise. From 1927 to 1930, as various studios updated equipment, the rate of 24 fps became standard for 35 mm sound film. At 24 fps the film travels through the projector at a rate of 456 millimetres (18.0 in) per second. This allowed for simple two-blade shutters to give a projected series of images at 48 per second, satisfying Edison's recommendation. Many modern 35 mm film projectors use three-blade shutters to give 72 images per secondâ€"each frame is flashed on screen three times.
Animation
In drawn animation, moving characters are often shot "on twos", that is to say, one drawing is shown for every two frames of film (which usually runs at 24 frames per second), meaning there are only 12 drawings per second. Even though the image update rate is low, the fluidity is satisfactory for most subjects. However, when a character is required to perform a quick movement, it is usually necessary to revert to animating "on ones", as "twos" are too slow to convey the motion adequately. A blend of the two techniques keeps the eye fooled without unnecessary production cost.
Animation for most "Saturday morning cartoons" is produced as cheaply as possible, and is most often shot on "threes", or even "fours", i.e. three or four frames per drawing. This translates to only 8 or 6 drawings per second, respectively.
Modern video standards
Modern video formats utilize a variety of frame rates. Due to the mains frequency of electric grids, analog television broadcast was developed with frame rates of 50Â Hz or 60Â Hz, sometimes with video being interlaced so more motion information could be sent on the same available broadcast bandwidth, and sometimes with video being broadcast at 25 or 30 fps with each frame doubled. Film, which was almost universally shot at 24 frames per second, could not be displayed at its native frame rate, which required pulldown conversion, often leading to "judder": to convert 24 frames per second into 60 frames per second, every odd frame is doubled and every even frame is tripled, which creates uneven motion. Other conversions have similar uneven frame doubling. Newer video standards support 120, 240, or 300 frames per second, so frames can be evenly multiplied for common frame rates such as 24 fps film and 30 fps video, as well as 25 and 50 fps video in the case of 300 fps displays. These standards also support video that's natively in higher frame rates, and video with interpolated frames between its native frames. Some modern films are experimenting with frame rates higher than 24 fps, such as 48 and 60 fps.
See also
- Delta timing
- Federal Standard 1037C
- Film-out
- Flicker fusion threshold
- Glossary of video terms
- High frame rate
- List of film formats
- MIL-STD-188
- Movie projector
- Moving image formats
- Time-lapse photography
- Video compression
References
External links
- "Temporal Rate Conversion"â€"a very detailed guide about the visual interference of TV, video & PC
- 15 fps vs. 30 fps vs. 60 fps: A Visual Comparisonâ€"Adobe Flash based compare test source